Bacharach Flue-Gas Sample Conditioning System Especificaciones Pagina 80
- Pagina / 86
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Parts & Service ECA 450
76 Instruction 0024-9400
Symptom
Probable Cause & Remedy
“NOXIDE Sensor Error” message
appears at bottom of display.
a. Analyzer was turned on with
probe sampling flue gas. Remove
probe from stack and restart.
b. NO sensor not zeroed at start up.
Turn analyzer off and then on to re-
zero all sensors. If error persists,
replace sensor.
“CO-LO Sensor Error” message
appears at bottom of display.
a. Analyzer was turned on with
probe sampling flue gas. Remove
probe from stack and restart.
b. CO-LO sensor not zeroed at start
up. Turn analyzer off and then on to
re-zero all sensors. If error persists,
replace sensor.
“CO-HI Sensor Error” message
appears at bottom of display.
a. Analyzer was turned on with
probe sampling flue gas. Remove
probe from stack and restart.
b. CO-HI sensor not zeroed at start
up. Turn analyzer off and then on to
re-zero all sensors. If error persists,
replace sensor.
“SO2 Sensor Error” message
appears at bottom of display.
a. Analyzer was turned on with
probe sampling flue gas. Remove
probe from stack and restart..
b. SO
2
sensor not zeroed at start up.
Turn analyzer off and then on to re-
zero all sensors. If error persists,
replace sensor.
“Pressure Sens. Error” message
appears at bottom of display.
a. Analyzer was turned on with
probe measuring a pressure is that
was outside the range of ±3 inches
of water (±7.47 mb/hPa, ± 747 Pa).
Ensure probe is sampling
atmospheric pressure and restart.
b. Sensor defective. Return to
Bacharach for replacement.
“Bad Calibration Entry” message
appears during calibration.
A calibration value was entered that
is outside the allowable range for
calibration. Apply a calibration gas
concentration or pressure value that
is within the range of the sensor
being calibrated as listed in the
calibration procedure.
- Model 450 1
- Notice: 2
- Table of Contents 3
- Contents ECA 450 4
- 1 Introduction 5
- 1.3 Technical Data 6
- Accuracy: 7
- 4 Instruction 0024-9400 8
- 1.4 Operation Overview 9
- Introduction ECA 450 10
- 6 Instruction 0024-9400 10
- 1.5.3 POWER (AC Adapter) 11
- 1.5.6 OPT (Option) 11
- 8 Instruction 0024-9400 12
- CALIBRATE 13
- 10 Instruction 0024-9400 14
- 2 Operation 15
- 2.3 Fuel Selection 16
- ECA 450 Operation 17
- Instruction 0024-9400 17
- Operation ECA 450 18
- 14 Instruction 0024-9400 18
- 2.7 Saving Test Data 20
- 2.8 Clearing Memory 20
- 18 Instruction 0024-9400 22
- 2.10 Printing Data 23
- 20 Instruction 0024-9400 24
- 2.12 Data Logging 26
- 24 Instruction 0024-9400 28
- Line 1: Column Headings 30
- 2.14.1 Thermocouple Method 31
- 28 Instruction 0024-9400 32
- 2.14.3 Thermometer Method 33
- 30 Instruction 0024-9400 34
- 2.16 Statistics Mode 36
- 34 Instruction 0024-9400 38
- 2.17.1 Temperature Units 40
- 2.17.2 Pressure Units 40
- 2.17.3 Pollution Units 40
- 2.17.4 Language 41
- 2.17.5 Date 41
- 2.17.6 Time 42
- 2.17.7 O 42
- Reference 42
- 2.17.8 Test ID 43
- 40 Instruction 0024-9400 44
- 42 Instruction 0024-9400 46
- 2.17.9 Display Timeout 47
- 2.17.10 Display Format 47
- 44 Instruction 0024-9400 48
- 2.17.11 Primary Air 49
- 2.17.12 Data Logging 49
- 2.17.13 Statistics 49
- 2.17.14 User Name 49
- 2.17.15 Keypad Sound 50
- 2.17.17 Print Pressure 52
- 2.17.18 Information 52
- 3 Calibration 53
- PRESSURE 54
- ECA 450 Calibration 55
- Calibration ECA 450 56
- 52 Instruction 0024-9400 56
- 3.7 Calibrate HC Sensor 58
- 3.8 Calibrate CO-LO Sensor 59
- 56 Instruction 0024-9400 60
- 3.9 Calibrate SO 61
- Sensor 61
- 3.10 Calibrate NO Sensor 62
- 3.11 Calibrate NO 63
- 3.12 Calibrate CO-HI Sensor 64
- 4 Maintenance 65
- Maintenance ECA 450 66
- 62 Instruction 0024-9400 66
- ECA 450 Maintenance 67
- 64 Instruction 0024-9400 68
- 4.4.1 O 69
- , CO, NO, NO 69
- , & SO 69
- Sensor Replacement 69
- 66 Instruction 0024-9400 70
- 4.4.3 HC Sensor Replacement 71
- PARTICULATE FILTER 72
- (Install with arrow pointing 72
- WATER TRAP/FILTER ASSEMBLY 73
- GAS HOSE 73
- RESET BUTTON 74
- 5 Troubleshooting 76
- 5.3 Error Symbols 77
- 5.4 Troubleshooting Guide 78
- ECA 450 Parts & Service 79
- 76 Instruction 0024-9400 80
- 78 Instruction 0024-9400 82
- 6 Parts & Service 83
- 6.2 Accessories 84
- 6.3 Service Centers 85
Relacionado con productos y manuales para De medición, control y control Bacharach Flue-Gas Sample Conditioning System
(100 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales